how do i check for corruption on cdmage?... On the scan for corruption button? i just did and no errors..

track01 starts at sector 150 (2sec pregap right?) and ends at 251.122
track02 starts at 251.273
so theres a 151 pregap.. 2 sec right?

i also check for 12bytes from PR on the first pregap and nothing everything is fine

so im stuck right now whats the next step? should i use EAC with these findings?... or is my rip complete (datawise) for submit? kind of lost rigth now...

So, once you know the disc's offset, you can dump in your other drives without counting garbage data. Let's say that px_d8 gave you +14. You subtract the drive's +12, telling you that the disc is a common +2. So, if you wanted to dump it in your DVR-112D, you'd use +48 + +2 = +50 in EAC's offset correction, or -24 + +2 = -22 in your LG drive. EAC will give a bad result for Track 2 when the combined offset is negative, so you'd best use another drive with a positive combined offset or PerfectRip in that case.

What the offset does is shift the position of the audio data. If you have +14 combined and you sector view the 2nd track, you'll see that there are 56 bytes of 00 (4 bytes per sample) preceding the audio data. In the case of a negative offset, the track will actually be pulled into the earlier sector.

i see that my plextor is perfect for the saturn and sega cd guide might give it a try with that guide, but i would like to know a bit more about the offset too 

As far as I know, you can't accurately know a CD's offset if the 'combined offset' is negative (unless your drive supports the 'px_d8' program), and you can't dump audio tracks unless you know the CD's offset.

I kept having this problem with -12 and -647 disks (because my drive was only +6).  I finally bought a
LG Electronics - DVDRAM GH24NS50 drive off Amazon that is +667 and I haven't had that problem since.
The only downside to the GH24NS50 is that it doesn't support 'over-read' so I have to use a different drive to to make sure it doesn't cut any data off the end of the last audio track.

What is your drive's offset?

Try to rip with perfect rip, if that doesn't work, then you can extract the sectors manually with ISObuster (from-to) and attach them to the EAC dump of track02 with a hex editor. You need to know the combined offset of course, because it's likely you'll have to compensate for that... if you check the video guide posted in the stickies it can show you what to do. Although it has to do with large negative offset... it is the same technique.

it is my first rip..

first:
i have only one Data track01 and one Audio track02..
second:
gap on track 2 says 0.. how can i confirm it?

i already extracted the data file, im stuck just with the audio one... i saw a post a should use perfectrip i might cause i have an old plextor around the house.. but just to be sure the steps i should take...
my findings:

when i check view sectors on track 02 its all like this:
0000 : 30 30 30 30 30 30 30 30  30 30 30 30 30 30 30 30   0000000000000000
even up to 400 sectors up...

if i substract 149 from lba
0000 : 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00   ................

if i substract 150 from lba
0000 : 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00   ................

if i substract 151 from lba
0000 : 00 FF FF FF FF FF FF FF  FF FF FF 00 55 48 22 02   ............UH".
0010 : 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00   ................

if i substract 152 from lba
0000 : 00 FF FF FF FF FF FF FF  FF FF FF 00 55 48 21 02   ............UH!.

the first two digits of the last four numbers changes if i go bak on sectors.. 22...21...20..19..

what should i do?